| Age | Commit message (Collapse) | Author |
|---|
|
We are going to allow including the plugin sources built within the
ModemManager daemon binary; moving the sources within the daemon
sources directory makes it easier.
|
|
Subsystem vendor ID can be used for identifying PCI modems,
so expose the property.
|
|
We already have methods to query for interface specific attributes
like class/subclass/protocol, so add a new one for the interface
number, and make sure we use ATTRS{bInterfaceNumber} to load it
always, instead of assuming the ID_USB_INTERFACE_NUM property is set.
|
|
|
|
The original g_udev_device_get_property_as_int() uses strtol() without
an explicit base (i.e. 0) so that the base is autodetected from the
string whenever possible (e.g. if prefixes with '0x' it is treated as a
hexadecimal string).
But, for ID_USB_INTERFACE_NUM, we explicitly require reading the number
as an hex string, even if we don't have any '0x' prefix.
Reported-by: Matthew Stanger <stangerm2@gmail.com>
|
|
The mm_base_modem_grab_port() now receives a MMKernelDevice directly from the
plugin, which is then stored in the MMPort corresponding to the port.
This means that we have direct access to e.g. all properties set by udev rules
everywhere, and we don't need additional GUdevClient objects (e.g. like the one
used in the Huawei plugin to detect NDISDUP support during runtime).
For virtual ports (e.g. generated during unit tests), we have a new 'generic'
kernel device object which just provides the values from the kernel device
properties given during its creation.
|
|
Instead of relying constantly on GUdevDevice objects reported by GUdev, we now
use a new generic object (MMKernelDevice) for which we provide an initial GUdev
based backend.
|
|
All ports of the same modem reported by the kernel will all be associated with
a common 'uid' (unique id), which uniquely identifies the physical device. This
logic was already in place, what we do now is avoid calling it the 'sysfs
path' of the physical device, because we may not want to use that to identify
a device.
This logic now also enables the possibility of "naming" the modems in a unique
way by setting the "ID_MM_PHYSDEV_UID" property in the "usb_device" that owns
all the ports.
E.g. a custom device has 4 modems in 4 different USB ports. The device path of
each USB device will always be the same, so the naming rules could go like this:
$ vim /usr/lib/udev/rules.d/78-mm-naming.rules
ACTION!="add|change|move", GOTO="mm_naming_rules_end"
DEVPATH=="/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.5/4-1.5.1", ENV{ID_MM_PHYSDEV_UID}="USB-MODEM-1"
DEVPATH=="/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.5/4-1.5.2", ENV{ID_MM_PHYSDEV_UID}="USB-MODEM-2"
DEVPATH=="/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.5/4-1.5.3", ENV{ID_MM_PHYSDEV_UID}="USB-MODEM-3"
DEVPATH=="/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.5/4-1.5.4", ENV{ID_MM_PHYSDEV_UID}="USB-MODEM-4"
LABEL="mm_naming_rules_end"
Each of the modems found will have a unique UID retrieved from the previous list
of rules. Then, "mmcli" has also been updated to allow using the UID instead of
the modem DBus path or index, e.g.:
$ sudo mmcli -m USB-MODEM-1
/org/freedesktop/ModemManager1/Modem/0 (device id '988d83252c0598f670c2d69d5f41e077204a92fd')
-------------------------
Hardware | manufacturer: 'ZTE CORPORATION'
| model: 'MF637'
| revision: 'BD_W7P673A3F3V1.0.0B04'
| supported: 'gsm-umts'
| current: 'gsm-umts'
| equipment id: '356516027657837'
-------------------------
System | device: 'USB-MODEM-1'
| drivers: 'option'
| plugin: 'ZTE'
| primary port: 'ttyUSB5'
| ports: 'ttyUSB5 (at)'
...
$ sudo mmcli -m USB-MODEM-1 --enable
...
|
|
This patch makes declarations bind to definitions within the same module
to prevent the potential ambiguity if referenced directly.
AddressSanitizer think they violated one definition rule, although
those symbols are accessed by address through their modules and do
not depend on the order of the libararies loaded.
|
|
|
|
|
|
The probing logic expects either one or the other right now. In this case, it is
just simpler to include the Nozomi-related VID in the vendor filter, and remove
the product filter.
|
|
Both the ModemManager daemon and the mmcli will now include `libmm-glib.h' only.
We also handle two new special `_LIBMM_INSIDE_MM' and `LIBMM_INSIDE_MMCLI'
symbols, which if included before the `libmm-glib.h' library allow us to:
* Don't include the libmm-glib high level API in the ModemManager daemon, as
the object names would clash with those in the core.
* Define some of the methods of helper objects to be included only if compiling
ModemManager daemon or the mmcli.
|
|
Different ports of the same modem may get handled by different drivers. We
therefore need to provide a list of drivers (new `Modem.Drivers' property with
signature 'as') instead of just one (removed `Modem.Driver' property with
signature 's').
$ sudo mmcli -m 0 | grep drivers
| drivers: 'qcserial, qmi_wwan'
|
|
|
|
There's no real point in maintaining a separate `MMPlugin' interface, as all the
plugins will inherit from `MMPluginBase', so just merge them and simplify
everything.
|
|
Before this, we only exported the modem to DBus when all ports were organized,
in order to make sure that we select as primary port the one we really want and
not the first AT port grabbed. Given that to get all the ports organized we also
needed to wait to get all the ports grabbed, we can now also defer the creation
of the modem object until all the ports get grabbed. This allows us to create
different types of objects based on the ports available (e.g. we can now create
QMI-supported modem objects if we see a QMI port around).
|
|
We shouldn't depend on any header file from the previous implementation.
|
|
|
