| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Flag as deprecated the old names, and define new ones based on the
defined UTRAN band numbers, equivalent to what was done for LTE bands.
|
|
New definitions for not so common GSM frequency bands.
|
|
Using an intermediate constant variable breaks compilation with C
compilers, as these variables cannot be used as initializers.
Instead, define a deprecated type and cast all deprecated symbols to
that type. We lose the information about what the new replacement
symbol is, but we don't break compilation.
E.g.:
test.c: In function ‘main’:
test.c:8:5: warning: ‘MMModemBandDeprecated’ is deprecated [-Wdeprecated-declarations]
printf ("band: %d\n", MM_MODEM_BAND_U2100);
^~~~~~
|
|
Those Roman numeral suffixes in MM_MODEM_BAND_EUTRAN_* were replaced
with 1, 2, 3, ..., etc. This patch adds a compatibility header,
ModemManager-compat.h, to alias the old MM_MODEM_BAND_EUTRAN_* values to
the new values.
|
|
3GPP TS 36.101 Table 5.5-1 refers the E-UTRA operating bands as 1, 2, 3,
..., etc.
|
|
Introduce "sms only" and "CSFB not preferred" home/roaming states to be reported
for the CS context, while already registered on LTE.
Based on 3GPP TS 27.007 v13.5.0.
|
|
v4: modems/providers may not return DNS servers and not all modems
support DHCP, so lack of DNS servers should not indicate a bearer
IP method of "DHCP". IP config daemon/scripts already have to handle
missing DNS anyway.
v6: IPv6 requires SLAAC or DHCPv6 as part of the specification, so for
now we assume modems will support it. Provide all the info the modem
sent, but if there is any missing information use an IP method of
"DHCP" to indicate that info should be obtained via SLAAC/DHCPv6. Only
use an IP method of "STATIC" when all basic properties are given by
the modem.
|
|
|
|
|
|
But keep the retries when the frame marker isn't found.
https://bugzilla.gnome.org/show_bug.cgi?id=708861
|
|
|
|
Standard GPS setup (raw/nmea) will both enable the GPS module and take full
control of the GPS port. This prevents other processes from reading the NMEA
traces from e.g. a tty. In order to handle this, a new 'unmanaged' GPS location
source is introduced, which will just enable/disable the GPS module, without
reading anything from the GPS port. Of course, both raw/nmea and unmanaged
setups cannot be enabled at the same time.
|
|
Even if the IPv6 bearer method is DHCP, the client should use SLAAC
(eg, IPv6 Router Solicitations, Router Adverisements, and possibly
DHCPv6) to determine the correct prefix and DNS information. In
some cases, even with the DHCP method, and IPv6 "address" will be
given which should be assigned to the data port before beginning
an IP addressing as the mobile network may expect this address
to be used.
|
|
|
|
E-UTRAN operating band 44 is specified in 3GPP release 11 (see Table
5.5-1 "E-UTRA operating bands" in 3GPP TS 36.101 version 11.2.0 Release
11).
|
|
We can use these to return better error messages if an operator
does not support the default subscription APN functionality,
and the user does not give us an APN.
|
|
|
|
Will be used in 3GPP2 SMS messages.
|
|
Will be used in 3GPP2 SMS messages.
|
|
|
|
MMModem3gppSubscriptionState enum
|
|
|
|
|
|
Introspection can't copy with a '.' in the value nicks, so just remove those.
Note: This could be considered an ABI break!
Bug #705641.
Patch based on a previous one from Christian Persch <chpe@gnome.org>.
|
|
We will expose a new 'Ports' property listing all ports currently known by a
given modem. Ports which are not used but are detected as being part of the
modem will be listed with an 'unknown' port type.
This change uses the new 'MMModemPortType' enum and the new 'MMModemPortInfo'
helper struct to handle these values in libmm-glib. The already available
'MMPortType' enum hasn't been re-used for the interface because it contains
values that we don't need (e.g. IGNORED).
The port list is now also included in the modem information command of mmcli:
$ sudo mmcli -m 0
/org/freedesktop/ModemManager1/Modem/0 (device id '97b7b99e3e2bea103880545b619fb05a3cc81b26')
-------------------------
System | device: '/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4'
| drivers: 'qcserial, qmi_wwan'
| plugin: 'Gobi'
| primary port: 'cdc-wdm0'
| ports: 'ttyUSB0 (qcdm), ttyUSB1 (at), cdc-wdm0 (qmi), wwp0s29u1u4 (net)'
https://bugzilla.gnome.org/show_bug.cgi?id=702678
|
|
|
|
|
|
And also make it a list of masks, specifying which are the specific combinations
supported, not just one mask with all.
E.g.:
-------------------------
Hardware | manufacturer: 'Sierra Wireless, Incorporated'
| model: 'MC7710'
| revision: 'SWI9200X_03.05.19.04ap r5475 carmd-en-10527 2012/09/17 17:57:14'
| supported: 'gsm-umts
| gsm-umts, lte'
| current: 'gsm-umts, lte'
| equipment id: '358178040668164'
|
|
We want to expose in the Modem interface the list of supported IP families, and
the easiest way to do so is to have the IP family as flags, and provide in the
interface a single enum.
Also, a value of 0 for a MMBearerIpFamily specifies that no flags are set, so
just rename it to 'NONE'.
And add a new 'ANY' value which sets all flags to 1.
|
|
|
|
We don't want to support only 'relative' validity, so don't assume that the
Validity property will always be a uint32 value.
Instead, we define the Validity propery as '(uv)' tuple, where the first value
(a MMSmsValidityType) specifies the type of validity, and the second value is
a variant formatted accordingly to what the validity type specifies (e.g. a
uint32 value if the type is MM_SMS_VALIDITY_TYPE_RELATIVE).
|
|
We will check each string with our custom filter before even trying to
parse them. A MM_SERIAL_ERROR_PARSE_FAILED error will be issued whenever the
string doesn't match the filter.
|
|
Used initially when we don't know the current activation state.
|
|
We currently implement 'SIM missing' and 'SIM error', which are probably the
most common ones.
|
|
Going into/outof low-power state is now a user-requested action.
|
|
|
|
For bearers using STATIC or DHCP IP method, the modem itself is the one
negotiating authentication with the network. The new `allowed-auth' property
allows users to specify which authentication method(s) are allowed to be used.
See the following NetworkManager commit for more reference:
commit 34aef8aaaa09b7473b9496aa49e550bd2def03f8
Author: Andrew Bird <ajb@spheresystems.co.uk>
Date: Thu Mar 15 16:19:43 2012 -0500
|
|
|
|
|
|
Image types of `MM_FIRMWARE_IMAGE_TYPE_GENERIC' will expose only the mandatory
parameters. Other vendor-specific images may expose other properties.
|
|
Given only for STATUS REPORT SMS messages.
|
|
It will help deciding the type of message.
|
|
Instead of using a predefined set of string values for 'ip-type' in
Modem.CreateBearer() and Simple.Connect(), we'll use an enumeration. The
implementation will then need to convert the requested IP family type to e.g.
the correct PDP type in 3GPP modems.
This change also consolidates the use of enums in dictionary properties when
possible to do so, as with the Rm Protocol.
|
|
Before this, we only exported the modem to DBus when all ports were organized,
in order to make sure that we select as primary port the one we really want and
not the first AT port grabbed. Given that to get all the ports organized we also
needed to wait to get all the ports grabbed, we can now also defer the creation
of the modem object until all the ports get grabbed. This allows us to create
different types of objects based on the ports available (e.g. we can now create
QMI-supported modem objects if we see a QMI port around).
|
|
|
|
|
|
It was a bitmask once...
|
|
...instead of ${prefix}/include/mm
|
|
Modems which end up being found unusable (e.g. no SIM, fatal SIM error, no
capabilities) will be exposed in DBus, but just with the Modem interface and
in a FAILED state which allows no actions.
|
