diff options
Diffstat (limited to 'introspection')
| -rw-r--r-- | introspection/org.freedesktop.ModemManager1.Modem.Signal.xml | 97 |
1 files changed, 92 insertions, 5 deletions
diff --git a/introspection/org.freedesktop.ModemManager1.Modem.Signal.xml b/introspection/org.freedesktop.ModemManager1.Modem.Signal.xml index fa85d5d3..93b2996f 100644 --- a/introspection/org.freedesktop.ModemManager1.Modem.Signal.xml +++ b/introspection/org.freedesktop.ModemManager1.Modem.Signal.xml @@ -3,7 +3,8 @@ <!-- ModemManager 0.8 Interface Specification - Copyright (C) 2013 Aleksander Morgado <aleksander@gnu.org> + Copyright (C) 2013-2021 Aleksander Morgado <aleksander@aleksander.es> + Copyright (C) 2021 Intel Corporation --> <node name="/" xmlns:doc="http://www.freedesktop.org/dbus/1.0/doc.dtd"> @@ -18,14 +19,27 @@ registered in the cellular network. 3GPP devices will require a valid unlocked SIM card before any of the features in the interface can be used. + + There are two different ways defined to use the interface: either enabling + peridic polling (with the Setup() method), or configuring the device with + thresholds so that it reports the value updates automatically (with the + SetupThresholds() method, since 1.20). + + Both Setup() and SetupThresholds() can also be used at the same time if + required, e.g. if they report different signal quality measurement types. --> <interface name="org.freedesktop.ModemManager1.Modem.Signal"> <!-- Setup: - @rate: refresh rate to set, in seconds. 0 to disable retrieval. + @rate: refresh rate to set, in seconds. Use 0 to disable periodic polling. - Setup extended signal quality information retrieval. + Enable or disable the extended signal quality information retrieval via + periodic polling. + + Polling is less than optimal; a better way to be notified of extended + signal quality updates is to configure the modem to trigger the reports + when the signal changes, i.e. with SetupThresholds(). Since: 1.2 --> @@ -34,16 +48,89 @@ </method> <!-- + SetupThresholds: + @settings: threshold values to set. + + Setup thresholds so that the device itself decides when to report the + extended signal quality information updates. + + The thresholds configured via this method specify the delta between + specific signal quality measurements that would trigger a report by the + modem. For example, the user may want to be notified every time the + signal RSSI changes more than 10dBm, so a value of 10 would be + configured as <literal>"rssi-threshold"</literal>. + + The device may not support this kind of threshold setting, and instead + support fixed signal levels as thresholds (e.g. trigger reports when + signal RSSI crosses -90dBm). On these devices, the threshold configured + by the user as a difference between measurements is converted to fixed + signal levels automatically, depending on the expected range for each of + the configured values. E.g. if the user configures 10dBm as + <literal>"rssi-threshold"</literal>, the fixed signal levels could be + automatically set to -100dBm, -90dBm, -80dBm, -70dBm and -60dBm. + + <variablelist> + <varlistentry><term><literal>"rssi-threshold"</literal></term> + <listitem> + The difference of signal RSSI measurements, in dBm, that should + trigger a signal quality report update, given as an unsigned + integer (signature <literal>"u"</literal>). Use 0 to disable this + threshold. + </listitem> + </varlistentry> + <varlistentry><term><literal>"error-rate-threshold"</literal></term> + <listitem> + A boolean value, indicating whether signal quality report updates + should be triggered when error rate measurements change (signature + <literal>"b"</literal>). + </listitem> + </varlistentry> + </variablelist> + + If any of the settings is not given as input, the corresponding threshold + will be considered disabled, and device defaults will apply. + + Since: 1.20 + --> + <method name="SetupThresholds"> + <arg name="settings" type="a{sv}" direction="in" /> + </method> + + <!-- Rate: - Refresh rate for the extended signal quality information updates, - in seconds. A value of 0 disables the retrieval of the values. + Refresh rate, in seconds, for the extended signal quality information + periodic polling, as configured via the Setup() method. + + A value of 0 indicates the periodic polling is disabled. Since: 1.2 --> <property name="Rate" type="u" access="read" /> <!-- + RssiThreshold: + + The difference of signal RSSI measurements, in dBm, that should trigger + a signal quality report update. + + A value of 0 indicates the threshold is disabled. + + Since: 1.20 + --> + <property name="RssiThreshold" type="u" access="read" /> + + <!-- + ErrorRateThreshold: + + Flag indicating whether signal quality report updates should be triggered + on error rate measurement changes. + + Since: 1.20 + --> + <property name="ErrorRateThreshold" type="b" access="read" /> + + <!-- Cdma: Dictionary of available signal information for the CDMA1x access |